Bay Networks 5000 Manual de servicio Pagina 100
- Pagina / 166
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installing and Operating BayStack ARN Routers
A-4
114200-D Rev 00
Configuring an Ethernet Interface for Network Booting
To configure any ARN Ethernet interface for network booting, use the following
command format:
ifconfig
[
-d
]
<interface>
[
<IP_address> <subnet_mask>
[
<next_hop_address>
]]
Table A-2 describes the
ifconfig
command settings for configuring the router’s
Ethernet interface.
<subnet_mask>
Specifies the IP subnet mask of the interface you set with
<interface>
.
Provide this address in dotted decimal notation.
<next_hop_
address>
Specifies the IP address of the next-hop router. Provide this address
in dotted decimal notation. Specify this address only if there are
intermediate routers between the router and the BootP server.
Table A-2. Ethernet Interface ifconfig Command Settings
Setting Description
Default Setting
-d
Resets the router IP interface settings to the default values. Resetting
an Ethernet interface makes it inactive in the network booting process.
(The output of the
getcfg
command shows the default as None.)
IP Connector Setting
<interface>
Specifies the IP connector you are configuring. Use the format
xcvr
<
port
#>.
IP Address Settings
<IP_address>
Specifies the IP address of the interface you set with
<interface>
.
Provide this address in dotted decimal notation.
<subnet_mask>
Specifies the IP subnet mask of the interface you set with
<interface>
.
Provide this address in dotted decimal notation.
<next_hop_
address>
Specifies the IP address of the next-hop router. Provide this address in
dotted decimal notation. Specify this address only if there are
intermediate routers between the router and the BootP server.
Table A-1. COM Interface ifconfig Command Settings
(continued)
Setting Description
- Installing and Operating 1
- BayStack ARN Routers 1
- Trademarks 2
- Statement of Conditions 2
- USA Requirements Only 3
- European Requirements Only 3
- Taiwan Requirements 4
- Canada Requirements Only 4
- Contents 7
- 114200-D Rev 00 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- How to Get Help 22
- Chapter 1 23
- Installing the ARN 23
- Preparing to Install the ARN 24
- Additional Equipment 26
- Rack-Mounting the ARN 28
- Caution: 33
- and Figure 1-7 34
- ARN0066A 39
- ARN0064A 40
- Digital line 41
- Reg. Number 4P8USA-31445-DE-N 42
- ARN0090B 43
- RJ-11 telephone 44
- DB-60 cable 46
- DB-25 connector ports 46
- Connecting a PC Console 47
- Connecting a Terminal Console 49
- Console cable plus 50
- Connecting a Console Modem 51
- Connecting the Power Cable 54
- Console Modem 55
- Redundant Power 55
- Where to Go Next 56
- Chapter 2 57
- Starting the ARN 57
- Using EZ-Install 61
- Interrupting the Boot Process 62
- Continuing with Netboot 64
- $) appears 70
- Chapter 3 73
- Operating the ARN 73
- Base Module LEDs 74
- Ethernet 10BASE-T LEDs 75
- Table 3-2 75
- Expansion Module LEDs 77
- Adapter Module LEDs 78
- Table 3-10. ISDN BRI LEDs 79
- Table 3-13. X.25 PAD LEDs 80
- Table 3-14. V.34 Modem LEDs 81
- Table 3-15. Boot Status LEDs 82
- Protecting Memory Card Files 86
- Chapter 4 89
- Powering Down 90
- Removing the Filler Panel 91
- Metal tab on filler panel 92
- Removing an Adapter Module 93
- Installing an Adapter Module 94
- What to Do Next 96
- Appendix A 97
- Directed Netboot 97
- Using the ifconfig Command 98
- <IP_address> 99
- <interface> 99
- <interface> 100
- <next_hop_address> 100
- Examples of ifconfig Commands 102
- Using the bconfig Command 103
- Verifying Your Configuration 104
- Appendix B 107
- Before You Run Quick-Start 108
- Quick-Start procedure 109
- Filling Out the Worksheets 110
- Global Information Worksheet 111
- Router Protocol Worksheets 114
- OSPF Worksheet 115
- RIP Worksheet 115
- Wide Area Protocol Worksheets 118
- Frame Relay Worksheet 119
- PPP Standard Worksheet 120
- Appendix C 125
- ARN Technical Specifications 125
- Electrical Specifications 126
- Environmental Specifications 126
- (continued) 128
- CAB0107A 130
- Table C-4 131
- Token Ring STP Interface 132
- Token Ring UTP Interface 133
- Serial Interfaces 133
- Table C-7 134
- ISDN BRI U Interface 135
- ISDN BRI S/T Interface 136
- 56/64K DSU/CSU Interface 137
- FT1/T1 DSU/CSU Connections 137
- 12345678 138
- X.25 PAD Connections 139
- Local Console Connections 140
- Service Modem Connections 141
- Appendix D 143
- CAB0069B 146
- CAB0073A 147
- (continued) 149
- CAB0068A 152
- CAB0074A 153
- P6 Host port SELV 154
- Adapter Modules 156
Relacionado con productos y manuales para Software Bay Networks 5000
Software Bay Networks 5391 Manual de servicio
(20 paginas)
(20 paginas)
Software Bay Networks Event Manager Especificaciones
(73 paginas)
(73 paginas)
Software Bay Networks Baystream 7 Manual de servicio
(382 paginas)
(382 paginas)
Software Bay Networks BayRS Manual de usuario
(24 paginas)
(24 paginas)
Software Bay Networks 5000 Especificaciones
(185 paginas)
(185 paginas)
Software Bay Networks BayRS Manual de usuario
(16 paginas)
(16 paginas)
Software Bay Networks Baystream 7 Guía de usuario
(162 paginas)
(162 paginas)
Software Bay Networks 4000 Guía de instalación
(162 paginas)
(162 paginas)
Software Bay Networks FastLink II Especificaciones
(47 paginas)
(47 paginas)
Software Bay Networks Radius Manual de usuario
(96 paginas)
(96 paginas)
Software Bay Networks BayRS Manual de servicio
(18 paginas)
(18 paginas)
Software Bay Networks Radius Manual de usuario
(14 paginas)
(14 paginas)
Software Bay Networks ATMSpeed Especificaciones
(74 paginas)
(74 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales