Bay Networks CM 100 Manual de servicio Pagina 144
- Pagina / 200
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using the BayStack 350 Series 10/100 Autosense Switch
3-40
893-00992-D
Table 3-15 describes the Rate Limiting Configuration screen fields.
Table 3-15. Rate Limiting Configuration screen fields
Field Description
Port
Indicates the switch port numbers, from 1 to 26, that correspond to the field
settings in that row of the screen (for example, the field settings in row 2 apply to
switch port 2). Note that the settings in the All row (bottom row) apply to all 26
switch ports.
Packet Type
Allows you to select the packet types for rate limiting or viewing.
Default Value Both
Range Both, Multicast, Broadcast
Limit
Sets the percentage of port bandwidth allowed for forwarding the packet types
specified in the Packet Type field. When the threshold is exceeded, any additional
packets (specified in the Packet Type field) are discarded
1
.
1
Rate limiting is disabled if this field is set to None. This allows you to select and view the percentage of specific packet
types present in the network, without inadvertently limiting the forwarding rate.
Default Value None
Range None, 10%, 9%, 8%, 7%, 6%, 5%, 4%, 3%, 2%, 1%
Last 5 Minutes
This read-only field indicates the percentage of packets (of the type specified in
the Packet Type field) received by the port in the last five minutes. This field
provides a running average of network activity and is updated every 15 seconds.
Note that this field indicates the receiving port’s view of network activity,
regardless of the rate limiting setting.
Last Hour
This read-only field indicates the percentage of packets (of the type specified in
the Packet Type field) received by the port in the last hour. This field provides a
running average of network activity and is updated every five minutes.
Note that this field indicates the receiving port’s view of network activity,
regardless of the rate limiting setting.
Last 24 Hours
This read-only field indicates the percentage of packets (of the type specified in
the Packet Type field) received by the port in the last 24 hours. This field provides
a running average of network activity and is updated every hour.
Note that this field indicates the receiving port’s view of network activity,
regardless of the rate limiting setting.
- Using the BayStack 350 1
- Series 10/100 Autosense 1
- Trademarks 2
- Statement of Conditions 2
- USA Requirements Only 2
- European Requirements Only 2
- Canada Requirements Only 3
- Contents 7
- 893-00992-D 10
- Audience 19
- Organization 19
- Conventions 20
- Use of Enter, Type, and Press 21
- Other Conventions 21
- Bay Networks Customer Service 22
- How to Get Help 22
- Safety Messages 23
- Class A Product 25
- Hazardous Electrical Current 28
- Stacking Units in a Rack 29
- Hazardous Light Source 30
- Turning Off Power to the Unit 31
- Choosing a Baud Rate 33
- Changing Passwords 34
- Removing the Top Cover 36
- Chapter 1 37
- Getting Started 37
- Front-Panel Components 38
- Back-Panel Components 40
- Features 41
- Autosensing 43
- MultiLink Trunking 44
- Port Mirroring 44
- Flash Memory Storage 45
- SNMP MIB Support 45
- Network Configuration 46
- Power Workgroups 47
- VLAN Workgroups 49
- MultiLink Trunks 58
- (Figure 1-19 65
- Quick-Start Procedures 85
- Chapter 2 89
- Package Contents 90
- Site Preparation 91
- Software 92
- Environment 92
- Installation 93
- Wall Mounting 96
- Rack Mounting 98
- 10/100 Autosense Switch 100
- Connecting Port Cables 101
- 100BASE-FX Port Cables 102
- Connecting Power 103
- Verifying the Installation 104
- Using the Console Interface 105
- Chapter 3 105
- Console/Service Port Cabling 106
- Main Menu 111
- Caution: 112
- IP Configuration 113
- Choosing a BootP Request Mode 115
- SNMP Configuration 117
- System Characteristics 119
- Switch Configuration 121
- MAC Address Table 123
- VLAN Configuration 125
- (continued) 126
- Port Configuration 127
- MultiLink Trunk Configuration 130
- Table 3-9 describes the 131
- Port Mirroring Configuration 139
- Table 3-14. Monitoring Modes 141
- Rate Limiting Configuration 142
- Spanning Tree Configuration 151
- TELNET Configuration 159
- Software Download 162
- Display Event Log 165
- Excessive Bad Entries 166
- Write Threshold 166
- Reset to Default Settings 168
- Chapter 4 171
- Troubleshooting 171
- LED Indications 172
- Table 4-1. LED indications 173
- Port Connection Problems 175
- Port Interface 176
- Appendix A 177
- Technical Specifications 177
- Physical Dimensions 178
- Performance Specifications 178
- Data Rate 178
- Interface Options 179
- Safety Agency Certification 179
- Electromagnetic Emissions 179
- Declaration of Conformity 180
- Appendix B 181
- Server/Trunk Connections 181
- Appendix C 183
- MDI and MDI-X Devices 184
- Warning: 188
- Appendix D 189
- Default Settings 189
- Appendix E 193
- E-2 893-00992-D 194
Relacionado con productos y manuales para Redes Bay Networks CM 100
Redes Bay Networks CM 100 Manual de usuario
(8 paginas)
(8 paginas)
Redes Bay Networks CM 100 Manual de instrucciones
(66 paginas)
(66 paginas)
Redes Bay Networks Nautica 200 Manual de servicio
(136 paginas)
(136 paginas)
Redes Bay Networks CM 100 Manual de instrucciones
(140 paginas)
(140 paginas)
Redes Bay Networks 5000 Manual de usuario
(109 paginas)
(109 paginas)
Redes Bay Networks Nautica 200 Guía de instalación
(22 paginas)
(22 paginas)
Chief Manufacturing Swing Arm Mounts manuales
Manuales del propietario y guías del usuario para Mueble Chief Manufacturing Swing Arm Mounts.
Ofrecemos 1 manuales en pdf Chief Manufacturing Swing Arm Mounts para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales