Bay Networks Remote Annex Manual de usuario descargar pdf (Pagina 18)

Configuring the Nortel Networks Remote Access Concentrators and the DMS-10 for Remote Access.March 31, 1999 18

FIGURE 9. PRI WAN Example

Once the WANs are setup it is necessary to re-boot the RAC in order for the changes to

take effect. If the WAN switch_type has been changed the RAC will need to load a new

driver for the WAN port. This can take 5 to 10 minutes for the load to be completed. If the

RAC is set for self boot and the switch_type has been changed it will not take affect since

there is no download host.

WAN Generic Parameters

switch_type:*"ni2" buildout: 0dB

fdl_type: att num_b_channels: 0

analog_encoding: auto framing: ESF

line_code: B8ZS dnis: 0

ani: N digit_width: 0

inter_digit: 0 digit_power_1: 0

digit_power_2: 0 busy_signal_bits: 11

local_phone_number: "" auto_busyout_enable: N

callback_enable: N

WAN B/DS0 Channel Parameters

remote_address: 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0

0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0

0.0.0.0 0.0.0.0 0.0.0.0

ipx_network: 00000000 00000000 00000000 00000000

00000000 00000000 00000000 00000000

00000000 00000000 00000000

ipx_node: 00-00-00-00-00-00 00-00-00-00-00-00 00-00-00-00-00-00

00-00-00-00-00-00 00-00-00-00-00-00 00-00-00-00-00-00

00-00-00-00-00-00 00-00-00-00-00-00

sigproto: none none none none none none

none none none none none none

none none none none non

ringback: y y y y y y y y y y y y y y y y y y y y y y y

Establishes the IP address if they are assigned on

the B-Channel. Syntax is “set wan=W remote_address B

xxx.xxx.xxx.xxx 1”. This command will set 24 IP addresses

starting at xxx.xxx.xxx.xxx for all 24 B channels for

Sets address for IPX.

0 is the default for 24 channels

Extended SuperFrame

wan = W, where W equals 1 or 2. In this example they

Buildout for line length values are

0db, 7.5db, 15db, 22.5 db.

Use B8ZS for PRI.

Auto detects U-Law or A-Law codeing.

Choices areU-Law, A-Law or Auto.

( not discussed in this paper.)

Sets IPX Node Numbers ( not discussed in this paper.)

Sets B channel protocol, not used with PRI.

Not used on PRI

Sets interface to NI-2 PRI

are being set by the RADIUS server.

Setup of NI2 PRI

Note: These settings are accessed in the Admin portion of CLI. The command line is set wan=W where wan is either 1 or 2,

then keyword follower by parameter. Example set wan=1 switch_type ni2. For B channel settings “B” must be included in the argument and

then an increment value for the paramenter. Example set wan=2 b remote_adress xxx.xxx.xxx 1.

Bay Networks Remote Annex Manual de usuario Pagina 18

Comentarios a estos manuales

Bay Networks Remote Annex Manual de usuario Pagina 18

Comentarios a estos manuales

Relacionado con productos y manuales para Software Bay Networks Remote Annex